All Categories > Industrial Products > Engineering Composite Materials > Fiberglass Reinforced Polyester (FRP) > Glastic Standoff Insulators (Molded with a UL Recognized Flame Resistant Fiberglass Reinforced Thermoset Polyester Molding Compound) > View Items  
    Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Glastic Standoff Insulators (Molded with a UL Recognized Flame Resistant Fiberglass Reinforced Thermoset Polyester Molding Compound)

Check up to five results to perform an action.


Hi-Pot Tested to Assure Electrical Reliability
Glastic Standoff Insulators are molded of Underwriters laboratories Incorporated (UL) Recognized flame resistant fiberglass-reinforced thermoset polyester molding compound. Glastic Insulators 1603, 2015, 1461, 1872, 4610 and 4640 are UL Recognized according to UL Standard for Safety 891.

They feature shatter resistance and closer height tolerances than commonly available in porcelain insulators. Moisture and heat-resistance properties of Glastic Insulators are higher than those of conventional plastic insulators.

Voltage Rating
This is only meant to be a guide for indoor service. Insulators mounted within a suitable electrical cabinet are considered indoors even though the cabinet itself is outdoors. An insulator will withstand its rated voltage continuously but industry standards or other specifications may require a different spacing from conductor to ground for a particular voltage. Wet or dirty conditions may require derating an insulator.

Outdoor Use
Glastic Insulators are primarily intended to be used indoors or inside a suitable enclosure. Insulators 4610 and 4640 should not be used upside down if there is a possibility of the center hole filling with water.

UL Recognition
All Glastic Insulators are molded from UL Recognized molding materials (UL File E23525). When submitting your equipment to UL, you may need to furnish the molding material grade number used for a particular insulator. This information is available from Glastic Corporation. All of the molding materials used in Glastic Insulators have a generic relative Thermal Index of 130ºC electrical/130ºC mechanical. Glastic 1603, 2165, 2015, 1461, 1872, 4610 and 4640 Insulators are UL Recognized according to UL standard for Safety 891 (UL File E81713).




Compare Items
   
  Results 1 - 9 of 9 1 

Item #

Item Name

Tensile Strength

Cantilever Strength

Compression Strength

Torque Strength

Arc Resistance

2165 Panel and Switchboard Insulators 1000 lb 400 in/lb 8000 lb 12 ft/lb 180 sec
1603-2A Std. 600 Volt High Strength Standoff Insulator 2000 lb 1500 in/lb 20000 lb 25 ft/lb 180 sec
1603-2D Wide 600 Volt High Strength Standoff Insulator 2500 lb 1800 in/lb 20000 lb 30 ft/lb 180 sec
2015 Center-Post Insulators 2000 lb 1750 in/lb 20000 lb 50 ft/lb 180 sec
1461 Apparatus Standoff Insulators 3000 lb 3500 in/lb 60000 lb 50 ft/lb 180 sec
1872 Center-Post Insulators 2500 lb 3000 in/lb 25000 lb 50 ft/lb 180 sec
2035-1 A Frame Insulator 2500 lb 3600 in/lb 25000 lb N/A 180 sec
4610-10-E 5KV Standoff Insulator 3000 lb 6000 in/lb 20000 lb 200 ft/lb 180 sec
4640-15 15KV Standoff Insulator 5000 lb 10000 in/lb 20000 lb 285 ft/lb 180 sec
  Results 1 - 9 of 9 1 
twitterfacebookFlickrLinked InSite created by ThomasNet Web Solutions and powered by Navigator Platform
Foundry Service & Supplies, Inc. | Heat And Corrosion Resistant Industrial Insulation & Construction Materials