All Categories > Industrial Products > Engineering Composite Materials > Mica Composites > Cogetherm (M & P) (Up to 1800ºF Rigid Mica Composite Plate) > Item # Cogetherm-M  
    Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Item # Cogetherm-M, Cogetherm (M & P) (Up to 1800ºF Rigid Mica Composite Plate)

Cogetherm composites are designed for electro-mechanical and thermo-mechanical applications requiring one or more of the following properties: good machinability, excellent resistance to heat and/or open flame up to 1832ºF (1000ºC), low thermal conductivity, excellent electrical insulation, extremely high resistance to pressure, high resistance to impact (cracking, and chipping), impervious to most chemicals (including oil, grease, and water), asbestos-free, and ecologically safe and non-toxic.

Specifications  · Services  · Applications  · Machining  · Note



134 #/ft³

Compressive Strength at 68ºF

58000 psi

Compressive Strength at 392ºF

36250 psi

Flexural Strength

33350 psi

Tensile Strength

21750 psi

Dielectric Strength at 68ºF (20ºC)

625 V/mil

Dielectric Strength at 752ºF (400ºC)

325 V/mil

Dielectric Strength at 1112ºF (600ºC)

250 V/mil

Tracking Resistance

500 V

Volume Resistivity at 68ºF (20ºC)

>1016 ohm-cm

Volume Resistivity at 752ºF (400ºC)

>1012 ohm-cm

Volume Resistivity at 932ºF (500ºC)

>109 ohm-cm

Dielectric Loss at 160ºC

<1 %

Arc Resistance

>420 sec

Water Absorption

<1 % After 48 Hrs.

Maximum Operating Temperature

1292 ºF

Continuous Operating Temperature

932 ºF

Thermal Conductivity (Cross Plane) at 70ºF (21ºC)

1.01 BTU-in/hr-ft²-ºF

Thermal Conductivity (Cross Plane) at 500ºF (260ºC)

1.19 BTU-in/hr-ft²-ºF

Thermal Conductivity (Cross Plane) at 1000ºF (538ºC)

1.66 BTU-in/hr-ft²-ºF

Chemical Resistance




Untrimmed Plate Size

40 x 48 in
1016 x 1220

Usable Area

39.37 x 47.24 in
1000 x 1200


Up to 3 in

Tolerance on Thickness

Plate from 0.06” - 0.2” (1.5 - 5 mm) = ± 7%
Plate from 0.2” - 1.2” (5 - 30 mm) = ± 5%

Plate from 1.2” - 3” (30 - 76 mm) = ± 3%

Foundry Service and Supplies is a full-service fabricator with an unmatched reputation for quick turn-around and competitive pricing. We can easily handle any job for fabricated parts or stock sheets, from high production quantities to prototypes. Our quality and reliability make Foundry Service the best choice for all of your high temperature material requirements.

An excellent asbestos replacement material, Cogetherm can be used for many high temperature and electrical applications including the following:
  • Due to it’s excellent resistance to pressure at temperature, Cogetherm can be used for press insulation between the platen and the die to minimize the transfer of heat through the press mechanism, saving energy and decreasing process cycle times.
  • In the construction of induction and arc furnaces, Cogetherm is used as thermal and electrical insulation, taking advantage of it’s excellent permeability to high frequency waves.
  • In the field of induction heated equipment for brazing aluminum and copper discs to cooking utensils, Cogetherm is the ideal replacement for asbestos-cement plates.
  • Cogetherm is used in high voltage appliances due to it’s dielectric qualities and it’s resistance to electric arc and erosion.
  • In the distribution of gases through pipes, internal network connections are sealed using Cogetherm gaskets due to it’s resistance to pressure and it’s extraordinary thermal properties which result in the prevention of gas leaks, even during a fire.
  • Applications which require very clean, dust-free, abrasion resistant insulation with extremely low permeability to water and oil are well suited for Cogetherm. Some examples are insulators & pads for hot glass handling, electric circuit board parts and electrical insulating components, high temperature insulation for the food processing industry, and any application which requires a clean, dust-free material which will not dispel particles or fibers.

Up to .080” (2 mm) thick Cogetherm can be punched. We recommend that tools be fitted with draw rings. Above .080” (2 mm), we recommend machining (sawing, drilling, etc.) with high speed steel, tungsten carbide, or diamond tools and cutters. A hold-down plate is recommended to clamp the mica plate while it is being machined to prevent delamination. Cogetherm can be CNC, laser, or water jet cut.

The Cogetherm properties listed represent typical average values obtained in accordance with accepted test methods and are subject to normal manufacturing variations. They are supplied as a technical service and are subject to change without notice. Check with your supplier to assure current information.


·  Mica Composite Sheets - 2

·  Machined Mica Washers

·  Muscovite - Phlogopite Mica Sheets

·  Machined Cogetherm Mica Composite

·  Thick Mica Plate


Data Sheet for Cogetherm (M & P) (Up to 1800ºF Rigid Mica Composite Plate)
(PDF, 18KB)

twitterfacebookFlickrLinked InSite created by ThomasNet Web Solutions and powered by Navigator Platform
Foundry Service & Supplies, Inc. | Heat And Corrosion Resistant Industrial Insulation & Construction Materials