All Categories > Industrial Products > Cements, Coatings, & Mortars > High Temperature Cements > Sauereisen Cement (1800ºF+ High Strength Ceramic Cement and Crack Filler)  
    Printable Page     Email Email This Page     Save To Favorites Save To Favorites

Sauereisen Cement (1800ºF+ High Strength Ceramic Cement and Crack Filler)



A major manufacturer of home appliances utilizes No, 1 to seal the set screw (located at stem base indicated by arrow) of this thermostat, and thus assure maintenance of the proper temperature range calibration.

Physical properties were determined on specimens prepared under laboratory conditions using applicable ASTM procedures. Actual field conditions may vary and yield different result;. therefore data are subject to reasonable deviation. Data should not be used for specification purposes.





Specifications  · Strong Inorganic Adhesive  · Application / Curing  · Characteristics

Specifications

Coefficient of Thermal Expansion

6.2 x 10-6 in/in/ºF
11.2 x 10-6
cm/cm/ºC

Color

Off-White

Compressive Strength

3900 psi
274
kg/cm²

Dielectric Constant

3.5 to 6.0

Dielectric Strength at 70ºF (21ºC)

12.5 to 51.0 V/mil
490 to 2000
V/mm

Dielectric Strength at 750ºF (399ºC)

≤15.0 V/mil
588
V/mm

Dielectric Strength at 1475ºF (801ºC)

≤1.3 V/mil
51
V/mm

Maximum Service Temperature

1800 ºF
982
ºC

Modulus of Rupture

460 psi
32
kg/cm²

Shear Strength

710 psi
49
kg/cm²

Tensile Strength

410 psi
28
kg/cm²

Volume Resistivity at 70ºF (21ºC)

108 to 109 ohm-cm

Volume Resistivity at 750ºF (399ºC)

104 to 105 ohm-cm

Volume Resistivity at 1475ºF (801ºC)

102 to 103 ohm-cm


Strong Inorganic Adhesive
Appliances
Insulating
Assembling
Metals
Ceramics
Sealing

Sauereisen Insa-Lule Adhesive Cement No. 1 is specified throughout industry for assembling, insulating, heal treating, and cementing porcelain, glass, metal, and other materials. No. 1 is also used to replace sealing wax, bolts, nuts, screws, and mica because it readily adheres to practically any non-plastic surface which is clean and free from oil and grease.



Application / Curing
Sauereisen No. 1 is supplied as a ready mixed paste and may be applied by brushing, dipping, or spraying. Depending on the application, No. 1 maybe thinned with Sauereisen Thinning Liquid No. 14.
No. 1 is suitable for use on production lines with mechanical dispensers or applicators as it will not harden in the equipment.
Hardening is by air drying into a white porcelain-like body. In applications where the cement is not exposed to the air, such as in spark plug or fuse assembling, it must be dried by baking at low temperatures.
The cement is also available in a powder form known as Sauereisen Insa-Lute Adhesive Cement No. P-1 (Powder). It is mixed with water to obtain the proper consistency when the cement is used, it has the same characteristics as No. 1 (Paste).



Characteristics
  • Heal conductive and thermal shock resistant
  • Insulates electricity
  • Resists all acids (except hydrofluoric)
  • Resists oil and fire
  • Resists temperature to 1800ºF (962ºC)
  • More economical than resins or silicones
  • Replaces resins for high temperature applications
  • Good mechanical bond
  • Can be colored
  • One part cement, ready to use
  • Odorless




 DOWNLOADS 

Data Sheet for Sauereisen Cement (1800ºF+ High Strength Ceramic Cement and Crack Filler)
(PDF, 134KB)


twitterfacebookFlickrLinked InSite created by ThomasNet Web Solutions and powered by Navigator Platform
Foundry Service & Supplies, Inc. | Heat And Corrosion Resistant Industrial Insulation & Construction Materials