All Categories > Industrial Products > Cements, Coatings, & Mortars > High Temperature Cements  
 

High Temperature Cements


Click on a Product to view details.

CalCoat-127 (1200ºF Insulating and Finishing Cement)

CalCoat-127 (1200ºF Insulating and Finishing Cement)


CalCoat-127 is a proprietary blend of hydraulic cement, calcium silicate and inorganic mineral fibers, with corrosion inhibitors, that provides a smooth finish over high-temperature insulation. No wire mesh is required. It can also be used as a general-purpose insulating cement, as it is easy to trowel and resists wetting after initial application. One bag will cover a minimum of 30 sq. ft. at 1” (2.8 square meters at 25 mm) thick. CalCoat-127 can be painted with water- or oil-base paints.
Cements, Coatings, & Mortars

Cal-Stik (1000ºF+ Calcium Silicate Based Adhesive)


Super Calstik is a modified, silicate-based glue. It sets quickly to provide a high temperature bond for porous insulating materials. Super Calstik is completely asbestos free.
Grefpatch-85 Patching Plaster (3000ºF 84% Alumina Patching Plaster)

Ceramic Fiber Moldable (2300ºF Air-Setting Ceramic Fiber Moldable Putty)


Kaowool® MOLDABLE
  • High-temperature putty
  • Ready to use
  • Easy to apply
  • Air dries and hardens
  • Regular and sticky version (SV)
Kaowool Moldable is a mixture of ceramic fiber, silica binders, and fillers which produces an insulating product with a sticky consistency. This type of mix is ideal for applications such as penetration seals, metal stud protection (as in ceramic cone anchors), and for patching refractory cracks and fissures. The temperature of Kaowool Moldable and any surface to which it is to be applied should be 70ºF (20ºC) or above to ensure proper adhesion.

Drying is possible at room temperature; but depending on thickness, may require an extended period of time. Heated, forced air drying is ...
Fused Silica Cement (99% Silica 2000ºF+ Cement)

Fused Silica Cement (99% Silica 2000ºF+ Cement)


Fused Silica Cement is a water based, inorganic cement for patching, joining, coating or repairing fused silica products, especially Fused Silica Foam-50 and slip cast fused silica from Foundry Service. Its composition is virtually 100% silica. Despite its high solids content, for low drying shrinkage, its pourable consistency permits easy application and usage by a variety of methods.
Grefpatch-85 Patching Plaster (3000ºF 84% Alumina Patching Plaster)

Morco Fibrous Adhesive (3000ºF Economical Ceramic Fiber Based Adhesive)


Type
An air-setting adhesive of thin consistency and high surface tension, designed primarily for applying ceramic wool modules to both vertical and horizontal surfaces and for cementing ceramic fiber boards and blankets to each other or to other refractory surfaces.

Air setting
Packed in 80 lb. or 55 lb. plastic pails.

Typical Test Data
According to ASTM Standard Test Methods, where applicable.
Quik-Cote (1200ºF Insulating and Finishing Cement)

Quik-Cote (1200ºF Insulating and Finishing Cement)


Quik-Cote is a mineral fiber hydraulic-setting thermal insulating and finishing cement. It is a dry mixture of mineral fiber pellets and other insulating fillers blended with hydraulic setting binders and corrosion inhibitors. When water is added, a highly plastic cement is formed with excellent trowelling and palming characteristics. The wet cement takes a hydraulic set in about 2 hours and, upon drying, provides a smooth, off-white, monolithic finish on the applied surface.
Sauereisen Cement (1800ºF+ High Strength Ceramic Cement and Crack Filler)

Sauereisen Cement (1800ºF+ High Strength Ceramic Cement and Crack Filler)


A major manufacturer of home appliances utilizes No, 1 to seal the set screw (located at stem base indicated by arrow) of this thermostat, and thus assure maintenance of the proper temperature range calibration.

Physical properties were determined on specimens prepared under laboratory conditions using applicable ASTM procedures. Actual field conditions may vary and yield different result;. therefore data are subject to reasonable deviation. Data should not be used for specification purposes.
Super-Stik (1900°F Insulating Cement)

Super-Stik (1900ºF Insulating Cement)


"Super-Stik" is a mineral fiber thermal insulating cement. It is composed of high temperature fiber pellets, blended in dry form with heat resistant binders and corrosion inhibitors. With the addition of water, a highly plastic insulating cement is formed, suitable for a wide variety of surfaces operating up to 1900ºF. This unique insulating material offers high thermal performance, out-standing wet and dry adhesion and excellent coverage.

This information is accurate and reliable to the best of our knowledge and will vary with manufacturing and testing tolerances. We have no control over installation workmanship, accessory materials or application conditions, and make no representation or expressed or implied warranty, either as to ...
twitterfacebookFlickrLinked InSite created by ThomasNet Web Solutions and powered by Navigator Platform
Foundry Service & Supplies, Inc. | Heat And Corrosion Resistant Industrial Insulation & Construction Materials